Next, clean the surface of the tiles from the solution with a brush without touching with stitches.

After laying ceramic tiles on the wall or floor is still one final construction operation - grouting own hands. Not a bad Grout ensure the conservation and sustainability of construction, will cover excellent appearance, emphasize linearity and geometry of the wall or floor plane. Types of rubbing materials
Grout made of cement or epoksydky. By his own cement grout composition identical with other system solve solutions, because they contain virtually the same components, solve but with the addition of a hardener or latex, which bred water. In retail grout can be both dry and ready-made, each of which has its own annotation consistency with training to work and its application to the work surface to help in this case, if you decide solve to perform grout seams with my hands.
Epoxy grout cement is different from its own plasticity, it has the strength, resistance to dynamic loads and constant attacks. Grout can be used for sealing seams from 6 to 12 mm depth. Closing more small cracks do not provide the desired properties, so that the characteristics of the material does not provide free penetration of microscopic cracks with a width of 2 MMI below.
Sealants are used to prevent joints between ceramic tiles from moisture absorption and subsequent darkening because property sealant provides solve prevention education moldy fungus. Sealing is based on the paint and silicone, so there was a synthetic material. Use sealant is necessary in areas with high humidity, such as a bathroom, toilet, shower, kitchen or other utility rooms, where abundance of water used. Width rubbing seams
Setting the width of weld joints between tiles may vary from 3 to 12 mm. At the beginning of laying tile width is set as the only option for the entire room. To change the width or lay tile without following the established parameter should not be, it would violate the overall geometry solve of the surface and break the look so picture tile and its texture will not match.
To seams were equal, using special devices - Crosses for tile with different sizes, which determine the width of future joints. At busy laying tile seam is less than 3 mm, this leads to the solution to cause grout is not possible, and with a width of more than 12 mm, applied grout drying can roztriskatysya. In any job best option would be a middle ground, but remember that when laying large tiles visually looks good seam that has no size 6 mm, and for smaller tiles - 3-4 mm. Grout epoksydkoy performed on joints less than 6 mm. Tips
Ready plytochnaya surface has complete coverage type, because its lines do not have clarity. Future grouting solve so good that gives a sense of satisfaction at work, waiting to get perfectly smooth and beautiful surface, which again and again I want to touch it, hold it by the hand and enjoy the work done. To work you need a prepared solution and simple tools in the form of a rubber spatula, grater, sponges, solve cleaning solve materials and water. Do not forget about personal protective equipment: gloves and glasses.
But first, you need to prepare the surface for processing, clean seams of cement, glue, inequalities, remove the tick and make sure that the adhesive mortar or cement completely prosoh. Glazed tiles can be subjected to rubbing treatment solution immediately, but when working with conventional ceramics must first lightly solve wet the edge of the tiles in order to process the adhesion between the tile and the mixture was held intense.
The prepared solution is applied to the joints between the tiles with confidence and effort. Movement should be rubbed, so that the seam should penetrate the maximum amount of solution. Work carefully, very time consuming, solve but the result will be the perfect finish walls and floors. When zatirke tile that has a distinct color, such as brown, green or blue, you should use a particular finished grout color or prepare it yourself using dyes.
The treatment of the entire surface with a spatula solve can be replaced by a more progressive view of applying grout, using a pastry solve bag or tube ready with silicone grout. But even in this case you need to go through all the seams by hand rubbing the mixture.
Next, clean the surface of the tiles from the solution with a brush without touching with stitches. After drying grout, solve tile surface is cleaned with a damp cloth and brush, and the layer of sealant that is aligned pipes.
Hello, my name is Ivanna designer and i I "foreman" of perennial solve experience. This blozi I will provide you with advice and decisions. I would be happy if you're constantly readers, and you can n