If Grout is selected correctly and be of poor quality, it will help to ensure that it cracked and v

To date, a mandatory element tile grout masonry is its seams. It provides not only improve the appearance of the entire the 5th wave stack, but also has a number of functional problems. Basically these include: waterproofing, protection from falling debris and dirt. Consider each of them. Functional task grout for joints the 5th wave
Grouting They are: Decorative the 5th wave and aesthetic. Trowellings produced different colors and color can be chosen for any decor; Waterproofing. This is especially important when processing tile bathroom and kitchen; Safety. Grout protects joints and cracks from getting various debris, dirt, dust and water.
If Grout is selected correctly and be of poor quality, it will help to ensure that it cracked and vykryshenyh the seams. Therefore, it is important to first select the correct grout. For example, when tile mounted on a cement paste or a good glue acquired specialized the 5th wave grout.
It is interesting that when proper performance grouting can mask and visually to correct defects were laying tile. But the poor quality grout spoil the impression of the most flawless and professional work done.
Cement grout for tile - is a dry mixture of cement (Portland cement), part of which may include special additives that improve its characteristics (eg, latex softener or hardener). Before using this grout, it is diluted with water or liquid latex.
Grouting - finishing stage of processing tile Grout This much prettier cement. In all sorts of colors, it can be produced with a bronze, silver and gold shimmer. Our assortment allows you to use the appropriate grout for any chosen color and type of tile or ceramic tile. Also, the Grout will last much longer than cement. It features high resistance to water and does not form mold and mildew.
This type of grout has a much higher cost and is complex to use. The fact that epoxy grout is very sticky - which is why it is quite difficult to apply, especially those who have no experience and services professionals are not cheap. If the thickness of the tile is less than 12 millimeters, and stitches in width not exceeding 6 mm, then evenly fill the grout to fail. In addition, it requires the 5th wave special construction tools, electronic scales.
Therefore, this technology the 5th wave is usually used in industrial and commercial areas, lined with large tiles with wide seams between them. But, in general, the end result and appearance justifies spent all her money and effort. Epoxy grout modified
This type of grout has properties and characteristics similar to both the properties and characteristics and cement the 5th wave and epoxy rubbing. It consists of Portland cement, so it can be used as ordinary cement grout, differing from it only slightly increased strength and greater ductility. For several reasons, it is rarely used; when working with it required a respirator.
This form is to provide the 5th wave a separate group as the process technology and grouting mosaics is much more difficult. Being in essence a type of tile mosaic has features which complicate treatment the 5th wave and grout surfaces. This small size of mosaic fragments, thus greatly increasing the total number of stitches. Most joints have a minimum gap of the order of 2 mm.
Decorative tile grout grouting process seams at the conclusion of tiles consists of several stages: First, the 5th wave work requires the following tools: rubber gloves, ready to grout, metal spatula, spatula, rubber, the 5th wave dust mask (for use with cement grout) the 5th wave cloth. If you are using cement grout, you will need a respirator; Throughout the process of rubbing is important to mix the solution the 5th wave in the bucket, so he was always gentle when applying it to new areas; Whichever grout you're going to use, you can not do without gloves; Rubber spatula gently wipe solution is applied around the joints. At this stage in any case can not use a metal spatula because it can leave marks on the tile itself; Overwritten each section seam scraper first one, then the other way. This should keep rubbing floats at an angle of 30 degrees to the tile; During the application should be tightly filled joints, not just flatten solution; Apply grout should be in a small area laid tile, about 1.2 m2; It is necessary to closely monitor the lack of original "shells" or holes in the grout joints. If such were formed, you should dip your finger into the solution, then they close the hole, while waiting for 10-15 seconds; Surplus grout removed metal spatula. And with a damp cloth, which must make a circular motion; Grout washed to floor